Edit & regenerate

Header

Project name Project address MEP engineer Submitted to Proposal no. Proposal date Drawings dated

Intro paragraph

Item A —

Equipment rows (tags / models / voltages / qty) aren't editable here — that's a scope change; re-run the job. One bullet per line below, no • needed.

Includes (10) Not included (8)

Item B —

Equipment rows (tags / models / voltages / qty) aren't editable here — that's a scope change; re-run the job. One bullet per line below, no • needed.

Includes (58)

Omega “Silver” Series vertical-stacked water-source heat pump – one-piece cabinet1,2,10
Generation-H construction and design, STANDARD EFFICIENCY
Custom cabinet heights for enhanced acoustic performance (no plenums required)1
Standard CW temperatures (60-90F boiler-tower application)
20-gauge galvanized steel cabinet w/ 1-inch acoustic insulation
Field-configurable factory discharge openings and 1.5-inch collars9,10
7-inch (standard) cabinet base-stand w/ neoprene isolation3
Microprocessor-based (standalone) control system w/ LED diagnostics and freeze protection
Non-fused disconnect switch
Fused low-voltage control circuit
Removable control access panel w/ site window for service convenience
Remote-mounted field thermostat connection4
25-50FT thermostat whips w/ plug connections (Fld)4
Direct-drive fan w/ multi-speed, permanently lubricated, ECM type fan motor
Unit-mounted <3-speed> fan-speed switch
Automatic fan speed control provisions (requires multistage thermostat)
Stainless steel (insulated) secondary drain pan
Factory-installed condensate overflow protection
Removable chassis w/ Molex electrical connections (Fld)6
Copper (insulated) coaxial condenser water heat exchanger
NC35 sound performance package
Chassis-rail vibration-isolation system for enhanced acoustic performance
Refrigerant R-454B
Field-configurable [12-inch] piping knock-outs for installation flexibility
Factory-installed (normally-closed) automatic isolation valve & automatic flow regulating valve
Supply/return 2000PSIG-rated flexible hoses (Fld)
o 2-way, 2-position manual shut-off valves
o Strainer (20 mesh)
Flush-with-wall (flanged) hinged acoustic return-air & chassis access panel (Fld)5,6
Steel (screw-less) double-deflection discharge grilles w/ OBDs (as required) (Fld)5,7,8
Insulated line of site baffle (as required)7
1-Inch (MERV-11) pleated-media throwaway filters – 2 SETS TOTAL (Fld)
Wall-mounted digital programmable WI-FI thermostat (Braeburn Model 8205) (Fld)
Freight included to first destination, full-size 53FT trailer, FOB FACTORY terms
Factory-authorized installation supervision
12/18 standard parts ONLY (no labor or refrigerant) warranty
Extended 4-year (5 years total) compressor parts ONLY (no labor or refrigerant) warranty
Notes:
1. Cabinet (custom) height to be coordinated for aesthetics and fit. See framing detail. Intermediate
flexible connection included to isolate ducted connections from wall framing. Top plenum to be hung,
connection by others. Cabinets ship with cardboard in place over return-air, sheet metal knockouts in
place over supply-air and piping connections for site protection.
2. Cabinets are to be mounted/anchored to slab by others.
3. Cabinet base-stand height to be coordinated for aesthetics and fit. See framing detail. There may be a
for 12-inch stands (as required).
4. Thermostats will be provided by others.
5. Standard paint colors ONLY. ADD/ALTERNATE for custom paint colors available, not included in this
BOM.
6. Chassis is fully removable via hinged access panel (i.e. without need for removal of).
7. OBDs and line of site baffles are to be provided (ONLY) for units serving multiple adjacent (free
discharge) rooms. Furthermore, OBDs will only be provided on the primary discharge opening as per
manufacturer’s recommendations.
8. Supply grilles will only be provided for standard discharge opening sizes; all others (i.e. ducted
instances) will be provided by others.
9. Supply-air extension collars, where required, will be by others.
10. For cabinets with ducted supply-air connections, all cabinets will ship with TOP discharge connections.
Contractor will be responsible to hang discharge plenum above cabinet in order to make duct
connections. All discharge plenums must be isolated from cabinet via flexible connection.

Not included (36)

Cupronickel or brazed-plate heat exchangers
Compressor sound blankets
Digital or inverter scroll compressors
HW heating coils of any type
Shrink wrap
Polar ionization systems
UV lights
Fuses or circuit breakers
Electric heating coils
Thermostat or sensor hanging
MERV-13, 14 supply-air filters
Filter gauges or dirty filter switches of any type
Custom paint colors
External relays for baseboard heat tie-in
External relays for compressor disable
Coil coatings of any type
External “SUPER W” isolation or acoustic pads
Wireless thermostat capability
Auxiliary drain pans, remote leak detection or BMS alarm point
Spring isolation of any type
Hanging rods of any type
Supply grilles or balancing dampers (ducted units)
Flexible ducted connections
Outside air dampers or connections
Dampers of any type
Condensate pumps
Smoke detectors
PT ports, air vents
Communication or BMS provisions (i.e. BACNet, INCOMM tie-in)
Factory risers or external piping
Spare parts or chassis (unless otherwise mentioned above)
Double handling, storage or freight reconsignment charges
Rigging/receiving, unit handling or installation of any type
Start-up labor or troubleshooting
Commissioning or training
Extended parts warranty or labor warranty (unless otherwise mentioned above)

Item C —

Equipment rows (tags / models / voltages / qty) aren't editable here — that's a scope change; re-run the job. One bullet per line below, no • needed.

Includes (20) Not included (24)

Item D —

Equipment rows (tags / models / voltages / qty) aren't editable here — that's a scope change; re-run the job. One bullet per line below, no • needed.

Includes (1) Not included (1)

Cancel Regenerating overwrites the draft .docx for this run and re-runs QA (~15s).

Header

Item A —

Item B —

Item C —

Item D —